VLAN Troubleshooting Sim
Refer to the exhibit.
Your colleague has built a Layer 2 network in your client locations. You must verify the configuration and fix any issues identified as per customer requirements.
Customer requirements:
+ Verify if switch ports are assigned correct VLANs as shown in topology. Identify and fix any misconfiguration found in three switches
+ Verify if trunk links are operational between switches and the IEEE 802.1Q trunk encapsulation method is used. Identify and fix any misconfiguration found in trunk configuration
+ Make sure ports connected between switches are set as trunk ports
We are not sure about the details but here are the faults in this sim:
– Native VLAN mismatch between SW1 & SW3
– Switchport mode mismatch: one in access mode while the other end in trunk mode -> need to change from access to trunk mode
– One port in VLAN 500 while other port in VLAN 600
Recommended commands to solve this sim: show int trunk, show vlan, show run.
You can download and practice this sim with Packet Tracer at: https://www.9tut.com/download/9tut.com_CCNA_VLAN_Troubleshooting_Sim.zip
Commands to fix the issues:
SW1, SW2:
interface e0/2
switchport mode access
switchport access vlan 500
interface e0/3
switchport mode access
switchport access vlan 600
SW3:
interface e0/0 (or interface e0/1 of SW1)
switchport trunk encapsulation dot1q
switchport mode trunk
switchport trunk native vlan … (must match the native VLAN on the other end, use “show int trunk” command on SW1 to check SW1 native VLAN)
Hello everyone,
Please share the CCNA 200-125 dump at — rajkot at sbb.rs
— I will take the exam next month. thank you!!!
Hello everyone,
Please share simulation software for the CCNA 200-125 exam at — rajkot at sbb.rs
— I will take the exam next month january 2020 . thank you!!!
Hi All
Kindly can anyone please share with me the lasted CCNA 200-125 exam my email address is:
I will take the exam next month January 2020. Thank you all in advance and God bless you all for the assistance and support.
Your prompt response in connection herewith will be highly appreciated
plz send me the last dumps
esawy 1020 @gmail .com
please send me latest dumps at zurreedigital @ gmail .com
Hellooooooo please send me the lastt drump , i take the exam next month daniel134 @ hotmail.es
Byeee :D
Hi I am gonna take my CCNA 200-125 exam. Can anyone please send me the dump question or the last exam question. would be helpful for me.
oa554537 @ gmail . com
Thanks in advance
Hi, could anyone send me the last dump? I’m gonna take the exam next month.
santys696 @gmail .com
Thank you!!!
Latest PT Lab and Dumps.
Don’t pay
Free download from here.
mycertexam.com/blog/2020/01/08/cisco-latest-questions-answers/
Sharing is Caring.
Only one command “show int switchport” on each switch will help you to resolve this sim.
How are you supposed to know what’s wrong or what to fix? Any help would be greatly appreciated!
ay dis bih on da test still
Can anyone forward latest CCNA dumps at hghiorsi at aol dot com. Thank you very much in advance.
hello
For ccna latest dumps email {email not allowed}
Please I am new here but I can see this is a great site great work please help me out did my ccna 200 -125 three days ago got 718 too bad please can any one help with the latest dumps pls if you can will be glad to receive it at {email not allowed}
Olu January 21st, 2020
Please I am new here but I can see this is a great site great work please help me out did my ccna 200 -125 three days ago got 718 too bad please can any one help with the latest dumps pls if you can will be glad to receive it on my mail at aweolufisayoademi @ gmail
Please Help with the latest dump help send it to my email aweolufisayoademi@ gmail dot com
Nice Troubleshooting.
Could you please send me the latest dump?
edno.jr @ hotmail com
Thanks.
1. Fix the native VLAN issue on SW3:
Sw3(config)#interface e0/0
Sw3(config-if)#switchport trunk native vlan 1
2. Fix the issue on SW2:
Sw2(config)#interface e0/2
Sw2(config-if)#switchport access vlan 500
3. Fix the issue on SW1:
Sw1(config)#interface e0/0
Sw1(config-if)#switchport trunk encapsulation dot1q
Sw1(config-if)#switchport mode trunk
@Annonymous (January 25th, 2020) thanks for posting here the solution. It’s very helpful.
Please Help with the latest dump help send it to my email poweredbycai2@ hotmail dot com
my exam on 2/2/2020 pls email me latest dump m-binhassan @ Hotmail
hello my exam will be in 07/02/2020 please send me the lastest dump by {email not allowed}
best answer is to set the SW3 fa0/2 to :Sw3(config-if)#no switchport trunk native vlan 100
hello my exam will be in 10/02/2020 please send me the lastest dump by {watsapp no 03340763310}
Hi guys, next week, I will make the exam. Please, anyone have the last dump to share ? leods26(at)hotmail(dot)com
where the questions are?
Questions
Your colleague has built a Layer 2 network in your client locations. You must verify the configuration and fix any issues identified as per customer requirements. Customer requirements: + Verify if switch ports are assigned correct VLANs as shown in topology. Identify and fix any misconfiguration found in three switches + Verify if trunk links are operational between switches and the IEEE 802.1Q trunk encapsulation method is used. Identify and fix any misconfiguration found in trunk configuration + Make sure ports connected between switches are set as trunk ports
Quick question with this lab. If on SW1 and SW2, VLANs 500 / 600 are setup for switchport mode access already, do you really have to use the same commands again listed above in the sim?
I’m going To have CCNA 200-125 exam on Feb 20. I would be glad if you share with me the latest questions. Thanks in advance Please new questions 7.
ilijaaajokvaaa @ gmaaail (.) com (aaa=a)